KHGES015FF3
Millipore Express® SHC, Opticap® XL Capsule
sterile, Opticap® XL 150, inlet connection diam. 3/4 in., pore size 0.5/0.2 μm, cartridge nominal length 3.8 in. (9.7 cm)
Manufacturer: Millipore
Synonym(S): Opticap Sterile XL 150 Millipore Express SHC 0.5/0.2 μm 3/4 in. TC/TC
Select a Size
| Pack Size | SKU | Availability | Price |
|---|---|---|---|
| 3 EA | KHGES015FF3-3-EA | In Stock | ₹ 37,822.14 |
KHGES015FF3 - 3 EA
In Stock
Quantity
1
Base Price: ₹ 37,822.14
GST (18%): ₹ 6,807.985
Total Price: ₹ 44,630.125
material
polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level
400
reg. compliance
meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility
irradiatedsterile
product line
Opticap® XL 150
feature
hydrophilic
manufacturer/tradename
Millipore Express®
parameter
≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s)
sterile filtration: suitable
L
9.7 cm (3.8 in.)
Related Products
Description
- General description: Device Configuration: Capsule
- Packaging: Double Easy-Open bag
- Other Notes: These products are manufactured in a facility which adheres to FDA Good Manufacturing Practices.
- Preparation Note: Sterilization Method3 autoclave cycles of 60 min @ 123 °C; not in-line steam sterilizable
- Analysis Note: Bacterial RetentionSamples were quantitatively retentive of a minimum Brevundimonas diminuta challenge concentration of 1 x 10⁷ CFU/cm² using ASTM® F838 methodology.
- Legal Information: ASTM is a registered trademark of American Society for Testing and Materials
- Disclaimer: EMD Millipore Corporation certifies that this product complies with the European Pressure Equipment Directive, 97/23/EC of 29 May 1997. This product has been classified under Article 3 § 3 of the Pressure Vessel Directive. It has been designed and manufactured in accordance with sound engineering practice to ensure safe use. In compliance with Article 3 § 3 of this Pressure Vessel Directive, this product does not bear the CE mark.
Compare Similar Items
Show Difference
material: polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level: 400
reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility: irradiatedsterile
product line: Opticap® XL 150
feature: hydrophilic
manufacturer/tradename: Millipore Express®
parameter: ≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s): sterile filtration: suitable
L: 9.7 cm (3.8 in.)
material:
polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level:
400
reg. compliance:
meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility:
irradiatedsterile
product line:
Opticap® XL 150
feature:
hydrophilic
manufacturer/tradename:
Millipore Express®
parameter:
≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s):
sterile filtration: suitable
L:
9.7 cm (3.8 in.)
material: polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level: 400
reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility: irradiatedsterile
product line: Opticap® XL 150
feature: hydrophilic
manufacturer/tradename: Millipore Express®
parameter: ≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s): sterile filtration: suitable
L: 9.7 cm (3.8 in.)
material:
polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level:
400
reg. compliance:
meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility:
irradiatedsterile
product line:
Opticap® XL 150
feature:
hydrophilic
manufacturer/tradename:
Millipore Express®
parameter:
≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s):
sterile filtration: suitable
L:
9.7 cm (3.8 in.)
material: polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level: 400
reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility: irradiatedsterile
product line: Opticap® XL 150
feature: hydrophilic
manufacturer/tradename: Millipore Express®
parameter: ≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s): sterile filtration: suitable
L: 9.7 cm (3.8 in.)
material:
polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level:
400
reg. compliance:
meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility:
irradiatedsterile
product line:
Opticap® XL 150
feature:
hydrophilic
manufacturer/tradename:
Millipore Express®
parameter:
≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s):
sterile filtration: suitable
L:
9.7 cm (3.8 in.)
material: polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level: 400
reg. compliance: meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility: irradiatedsterile
product line: Opticap® XL 150
feature: hydrophilic
manufacturer/tradename: Millipore Express®
parameter: ≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s): sterile filtration: suitable
L: 9.7 cm (3.8 in.)
material:
polyethersulfone polyethylene supportpolypropylene (gamma-stable)polypropylene housingpolypropylene vent cap (Gamma stable)polysulfone silicone seal
Quality Level:
400
reg. compliance:
meets FDA Indirect Food Additive requirements cited in 21 CFR 177-182 (all component materials)
sterility:
irradiatedsterile
product line:
Opticap® XL 150
feature:
hydrophilic
manufacturer/tradename:
Millipore Express®
parameter:
≤1.0 mL/min air diffusion at 2.8 bar (40 psig) and 23 °C (in water)1.0 bar max. differential pressure (15 psid) at 80 °C (Forward)1.0 bar max. inlet pressure (15 psi) at 80 °C100 psi max. differential pressure (6.9 bar) (intermittent)2.1 bar max. differential pressure (30 psid) at 25 °C (Reverse; intermittent)2.75 bar max. inlet pressure (40 psi) at 60 °C25 °C max. inlet temp.5.5 bar max. differential pressure (80 psid) at 25 °C (Forward)5.5 bar max. inlet pressure (80 psi) at 23 °C6.9 bar max. differential pressure (100 psid) at 25 °C (Forward; intermittent)6.9 bar max. inlet pressure (100 psi) at 23 °C (intermittent)80 psi max. differential pressure (5.5 bar) (continuous)80 psig max. inlet pressure
technique(s):
sterile filtration: suitable
L:
9.7 cm (3.8 in.)